P2 (286) Second Generation Processors

by Hanna Quassar.

Share
|
Homepage | Submit your article | Contact | TOS
More articles on memory processor motherboards and buses  

You are here: Categories » Computers and technology » Memory Processor Motherboards and buses

The second generation of PC processors allowed for a great leap in system speed and processing efficiency. With these chips we went from moving 8 bits of data around to moving 16 bits at a time. The following section details the second-generation PC processor, the 286.

286 Processors

The Intel 80286 (normally abbreviated as 286) processor did not suffer from the compatibility problems that damned the 80186 and 80188. The 286 chip, first introduced in 1982, is the CPU behind the original IBM PC AT (Advanced Technology). Other computer makers manufactured what came to be known as IBM clones, with many of these manufacturers calling their systems AT-compatible or AT-class computers.

When IBM developed the AT, it selected the 286 as the basis for the new system because the chip provided compatibility with the 8088 used in the PC and the XT. Therefore, software written for those chips should run on the 286. The 286 chip is many times faster than the 8088 used in the XT, and at the time it offered a major performance boost to PCs used in businesses. The processing speed, or throughput, of the original AT (which ran at 6MHz) is five times greater than that of the PC running at 4.77MHz.

286 systems are faster than their predecessors for several reasons. The main reason is that 286 processors are much more efficient in executing instructions. An average instruction takes 12 clock cycles on the 8086 or 8088, but takes an average of only 4.5 cycles on the 286 processor. Additionally, the 286 chip can handle up to 16 bits of data at a time through an external data bus twice the size of the 8088.

The 286 chip has two modes of operation: real mode and protected mode. The two modes are distinct enough to make the 286 resemble two chips in one. In real mode, a 286 acts essentially the same as an 8086 chip and is fully object-code compatible with the 8086 and 8088. (A processor with object-code compatibility can run programs written for another processor without modification and execute every system instruction in the same manner.)

In the protected mode of operation, the 286 was truly something new. In this mode, a program designed to take advantage of the chip's capabilities believes that it has access to 1GB of memory (including virtual memory). The 286 chip, however, can address only 16MB of hardware memory. A significant failing of the 286 chip is that it cannot switch from protected mode to real mode without a hardware reset (a warm reboot) of the system. (It can, however, switch from real mode to protected mode without a reset.) A major improvement of the 386 over the 286 is that software can switch the 386 from real mode to protected mode, and vice versa.

Only a small amount of software that took advantage of the 286 chip was sold until Windows 3.0 offered standard mode for 286 compatibility; by that time, the hottest-selling chip was the 386. Still, the 286 was Intel's first attempt to produce a CPU chip that supported multitasking, in which multiple programs run at the same time.

80287 Coprocessor

The 80287, internally, is the same math chip as the 8087, although the pins used to plug them into the motherboard are different. Both the 80287 and the 8087 operate as though they are identical.

In most systems, the 80286 internally divides the system clock by 2 to derive the processor clock. The 80287 internally divides the system-clock frequency by 3. For this reason, most AT-type computers run the 80287 at one-third the system clock rate, which also is two-thirds the clock speed of the 80286. Because the 286 and 287 chips are asynchronous, the interface between the 286 and 287 chips is not as efficient as with the 8088 and 8087.

Leave a comment or ask a question
Total comments: 0

Memory Processor Motherboards and buses Disclaimer

  • The e-articles directory is not responsible for any and all copyright infringements by writers and authors. If you suspect the information contained by this page for any copyright infringements, please contact us to investigate the issue
The evolution of Microprocessors from 1971 to the Present - It is interesting to note that the microprocessor had existed for only 10 years prior to the creation of the PC! Intel invented the microprocessor in 1971; the PC was created by IBM in 1981. Now mo (more...)
How SIMM DIMM and RIMM memory work - Originally, systems had memory installed via individual chips. They are often referred to as dual inline package (DIP) chips because of their designs. The original IBM XT and AT had 36 sockets on t (more...)
EDORAM ~ Extended Data Out RAM - In 1995, a newer type of memory called extended data out (EDO) RAM became available for Pentium systems. EDO, a modified form of FPM memory, is sometimes referred to as Hyper Page mode. EDO was inv (more...)
Troubleshooting Memory - Memory problems can be difficult to troubleshoot. For one thing, computer memory is still mysterious to people because it is a kind of "virtual" thing that can be hard to grasp. The other difficult (more...)
Guidelines when upgrading memory on older systems - When upgrading an older motherboard, it is sometimes impossible to match the installed memory. Some motherboards have 30-pin and 72-pin SIMM sockets, and many have both SIMM and DIMM sockets. I (more...)
Guidelines when upgrading memory in Pentium II/III/IV Celeron and Athlon systems - These systems are excellent candidates for memory upgrades. Early Pentium II systems often have only 16 MB of RAM. In the price-sensitive consumer Celeron market, many early systems shipped wit (more...)
Power6 Processor: World`s Fastest Processor - Increases the processing speed to 4.7 GHz A revolutionary device in the form of tiny chip has been designed by IBM which has put the world in wonders. Power6 is really a mind-blow (more...)
About Clocking - In computers, a serial signal is one in which the bits of data of the digital code are arranged in a series. They travel through their medium or connection one after another as a train of pulses (more...)
Hardware Flow Control in the Serial Interface - Several of the signals in the serial interface are specifically designed to help handle flow control. Rather than a simple on and off operation, however, they work together in an elaborate ritua (more...)
Software Flow Control in the Serial Interface - The alternate means of handshaking, software flow control, requires your serial peripheral and PC to exchange characters or tokens to indicate whether they should transfer data. The serial perip (more...)

 
free content
    Copyright © 2006 - 2012 e-articles.info.
The texts, articles and tutorials in the directory are property of their respective owners and authors.